Zum Inhalt springen

Änderungen von Dokument 3D Drucker

Zuletzt geändert von Fab!an am 2025/04/01 16:54
Von Version 15.1
bearbeitet von Fab!an
am 2024/04/08 08:25
Änderungskommentar: Neuen Anhang PrusaSlicer_config_MegaS_Printbed.stl hochladen
Auf Version 20.1
bearbeitet von loppermann
am 2024/04/08 08:27
Änderungskommentar: Neuen Anhang PrusaSlicer_config_MegaS_ClampCalibration.stl hochladen

Zusammenfassung

Details

Seiteneigenschaften
Dokument-Autor
... ... @@ -1,1 +1,1 @@
1 -XWiki.foorschtbar
1 +XWiki.loppermann
PrusaSlicer_config_MegaX.ini
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.loppermann
Größe
... ... @@ -1,0 +1,1 @@
1 +9.6 KB
Inhalt
... ... @@ -1,0 +1,304 @@
1 +# generated by PrusaSlicer 2.5.0 on 2023-01-10 at 21:09:30 UTC
2 +
3 +[print:0.20mm QUALITY @ Anycubic Mega X]
4 +avoid_crossing_perimeters = 0
5 +avoid_crossing_perimeters_max_detour = 0
6 +bottom_fill_pattern = monotonic
7 +bottom_solid_layers = 4
8 +bottom_solid_min_thickness = 0.5
9 +bridge_acceleration = 1000
10 +bridge_angle = 0
11 +bridge_flow_ratio = 0.95
12 +bridge_speed = 25
13 +brim_separation = 0
14 +brim_type = outer_only
15 +brim_width = 0
16 +clip_multipart_objects = 1
17 +compatible_printers =
18 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_MEGA_X.*/ and nozzle_diameter[0]==0.4
19 +complete_objects = 0
20 +default_acceleration = 1000
21 +dont_support_bridges = 1
22 +draft_shield = disabled
23 +elefant_foot_compensation = 0
24 +ensure_vertical_shell_thickness = 1
25 +external_perimeter_extrusion_width = 0.45
26 +external_perimeter_speed = 40
27 +external_perimeters_first = 0
28 +extra_perimeters = 1
29 +extruder_clearance_height = 35
30 +extruder_clearance_radius = 60
31 +extrusion_width = 0.45
32 +fill_angle = 45
33 +fill_density = 15%
34 +fill_pattern = gyroid
35 +first_layer_acceleration = 800
36 +first_layer_acceleration_over_raft = 0
37 +first_layer_extrusion_width = 0.42
38 +first_layer_height = 0.2
39 +first_layer_speed = 20
40 +first_layer_speed_over_raft = 30
41 +fuzzy_skin = none
42 +fuzzy_skin_point_dist = 0.8
43 +fuzzy_skin_thickness = 0.3
44 +gap_fill_enabled = 1
45 +gap_fill_speed = 40
46 +gcode_comments = 0
47 +gcode_label_objects = 1
48 +gcode_resolution = 0.0125
49 +gcode_substitutions =
50 +infill_acceleration = 1000
51 +infill_anchor = 2.5
52 +infill_anchor_max = 12
53 +infill_every_layers = 1
54 +infill_extruder = 1
55 +infill_extrusion_width = 0.45
56 +infill_first = 0
57 +infill_only_where_needed = 0
58 +infill_overlap = 25%
59 +infill_speed = 60
60 +inherits =
61 +interface_shells = 0
62 +ironing = 0
63 +ironing_flowrate = 15%
64 +ironing_spacing = 0.1
65 +ironing_speed = 15
66 +ironing_type = top
67 +layer_height = 0.2
68 +max_print_speed = 100
69 +max_volumetric_extrusion_rate_slope_negative = 0
70 +max_volumetric_extrusion_rate_slope_positive = 0
71 +max_volumetric_speed = 0
72 +min_bead_width = 85%
73 +min_feature_size = 25%
74 +min_skirt_length = 4
75 +mmu_segmented_region_max_width = 0
76 +notes =
77 +only_retract_when_crossing_perimeters = 0
78 +ooze_prevention = 0
79 +output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_MegaX_{print_time}.gcode
80 +overhangs = 1
81 +perimeter_acceleration = 800
82 +perimeter_extruder = 1
83 +perimeter_extrusion_width = 0.45
84 +perimeter_generator = arachne
85 +perimeter_speed = 50
86 +perimeters = 2
87 +post_process =
88 +print_settings_id =
89 +raft_contact_distance = 0.1
90 +raft_expansion = 1.5
91 +raft_first_layer_density = 90%
92 +raft_first_layer_expansion = 3
93 +raft_layers = 0
94 +resolution = 0
95 +seam_position = nearest
96 +single_extruder_multi_material_priming = 1
97 +skirt_distance = 2
98 +skirt_height = 3
99 +skirts = 1
100 +slice_closing_radius = 0.049
101 +slicing_mode = regular
102 +small_perimeter_speed = 25
103 +solid_infill_below_area = 0
104 +solid_infill_every_layers = 0
105 +solid_infill_extruder = 1
106 +solid_infill_extrusion_width = 0.45
107 +solid_infill_speed = 50
108 +spiral_vase = 0
109 +standby_temperature_delta = -5
110 +support_material = 0
111 +support_material_angle = 0
112 +support_material_auto = 1
113 +support_material_bottom_contact_distance = 0
114 +support_material_bottom_interface_layers = -1
115 +support_material_buildplate_only = 0
116 +support_material_closing_radius = 2
117 +support_material_contact_distance = 0.1
118 +support_material_enforce_layers = 0
119 +support_material_extruder = 1
120 +support_material_extrusion_width = 0.35
121 +support_material_interface_contact_loops = 0
122 +support_material_interface_extruder = 1
123 +support_material_interface_layers = 2
124 +support_material_interface_pattern = rectilinear
125 +support_material_interface_spacing = 0.2
126 +support_material_interface_speed = 80%
127 +support_material_pattern = rectilinear
128 +support_material_spacing = 2
129 +support_material_speed = 50
130 +support_material_style = grid
131 +support_material_synchronize_layers = 0
132 +support_material_threshold = 50
133 +support_material_with_sheath = 1
134 +support_material_xy_spacing = 60%
135 +thick_bridges = 1
136 +thin_walls = 0
137 +threads = 8
138 +top_fill_pattern = monotonic
139 +top_infill_extrusion_width = 0.4
140 +top_solid_infill_speed = 40
141 +top_solid_layers = 5
142 +top_solid_min_thickness = 0.7
143 +travel_speed = 180
144 +travel_speed_z = 0
145 +wall_distribution_count = 1
146 +wall_transition_angle = 10
147 +wall_transition_filter_deviation = 25%
148 +wall_transition_length = 100%
149 +wipe_tower = 0
150 +wipe_tower_bridging = 10
151 +wipe_tower_brim_width = 2
152 +wipe_tower_no_sparse_layers = 0
153 +wipe_tower_rotation_angle = 0
154 +wipe_tower_width = 60
155 +wipe_tower_x = 180
156 +wipe_tower_y = 140
157 +xy_size_compensation = 0
158 +
159 +[filament:Generic PLA @ Anycubic Mega X]
160 +bed_temperature = 60
161 +bridge_fan_speed = 100
162 +compatible_printers =
163 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_MEGA_X.*/
164 +compatible_prints =
165 +compatible_prints_condition =
166 +cooling = 1
167 +disable_fan_first_layers = 1
168 +end_filament_gcode = "; Filament-specific end gcode"
169 +extrusion_multiplier = 1
170 +fan_always_on = 1
171 +fan_below_layer_time = 100
172 +filament_colour = #FF3232
173 +filament_cooling_final_speed = 3.4
174 +filament_cooling_initial_speed = 2.2
175 +filament_cooling_moves = 4
176 +filament_cost = 25.4
177 +filament_density = 1.24
178 +filament_deretract_speed = nil
179 +filament_diameter = 1.75
180 +filament_load_time = 0
181 +filament_loading_speed = 28
182 +filament_loading_speed_start = 3
183 +filament_max_volumetric_speed = 10
184 +filament_minimal_purge_on_wipe_tower = 15
185 +filament_notes = ""
186 +filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
187 +filament_retract_before_travel = nil
188 +filament_retract_before_wipe = nil
189 +filament_retract_layer_change = nil
190 +filament_retract_length = nil
191 +filament_retract_lift = nil
192 +filament_retract_lift_above = nil
193 +filament_retract_lift_below = nil
194 +filament_retract_restart_extra = nil
195 +filament_retract_speed = nil
196 +filament_settings_id = ""
197 +filament_soluble = 0
198 +filament_spool_weight = 0
199 +filament_toolchange_delay = 0
200 +filament_type = PLA
201 +filament_unload_time = 0
202 +filament_unloading_speed = 90
203 +filament_unloading_speed_start = 100
204 +filament_vendor = Generic
205 +filament_wipe = nil
206 +first_layer_bed_temperature = 65
207 +first_layer_temperature = 215
208 +full_fan_speed_layer = 0
209 +inherits =
210 +max_fan_speed = 100
211 +min_fan_speed = 80
212 +min_print_speed = 15
213 +slowdown_below_layer_time = 20
214 +start_filament_gcode = "; Filament gcode\n"
215 +temperature = 210
216 +
217 +[printer:Anycubic Mega X]
218 +bed_custom_model =
219 +bed_custom_texture =
220 +bed_shape = 0x0,300x0,300x300,0x300
221 +before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]
222 +between_objects_gcode =
223 +color_change_gcode = M600
224 +cooling_tube_length = 5
225 +cooling_tube_retraction = 91.5
226 +default_filament_profile = "Generic PLA @MEGA"
227 +default_print_profile = 0.15mm QUALITY @MEGA
228 +deretract_speed = 50
229 +end_gcode = G1 E-1.0 F2100 ; retract\nG92 E0.0\nG1{if max_layer_z < max_print_height} Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} E-34.0 F720 ; move print head up & retract filament\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y105 F3000 ; park print head\nM84 ; disable motors
230 +extra_loading_move = -2
231 +extruder_colour = #808080
232 +extruder_offset = 0x0
233 +gcode_flavor = marlin
234 +high_current_on_filament_swap = 0
235 +host_type = octoprint
236 +inherits =
237 +layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
238 +machine_limits_usage = time_estimate_only
239 +machine_max_acceleration_e = 10000
240 +machine_max_acceleration_extruding = 1250
241 +machine_max_acceleration_retracting = 1250
242 +machine_max_acceleration_travel = 1500,1250
243 +machine_max_acceleration_x = 3000
244 +machine_max_acceleration_y = 2000
245 +machine_max_acceleration_z = 60
246 +machine_max_feedrate_e = 60
247 +machine_max_feedrate_x = 500
248 +machine_max_feedrate_y = 500
249 +machine_max_feedrate_z = 6
250 +machine_max_jerk_e = 5
251 +machine_max_jerk_x = 10
252 +machine_max_jerk_y = 10
253 +machine_max_jerk_z = 0.4
254 +machine_min_extruding_rate = 0,0
255 +machine_min_travel_rate = 0,0
256 +max_layer_height = 0.36
257 +max_print_height = 305
258 +min_layer_height = 0.07
259 +nozzle_diameter = 0.4
260 +parking_pos_retraction = 92
261 +pause_print_gcode = M601
262 +print_host =
263 +printer_model =
264 +printer_notes = Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_MEGA_X\nPRINTER_HAS_BOWDEN
265 +printer_settings_id =
266 +printer_technology = FFF
267 +printer_variant = 0.4
268 +printer_vendor =
269 +printhost_apikey =
270 +printhost_cafile =
271 +remaining_times = 1
272 +retract_before_travel = 1.5
273 +retract_before_wipe = 60%
274 +retract_layer_change = 1
275 +retract_length = 6
276 +retract_length_toolchange = 10
277 +retract_lift = 0.075
278 +retract_lift_above = 0
279 +retract_lift_below = 204
280 +retract_restart_extra = 0
281 +retract_restart_extra_toolchange = 0
282 +retract_speed = 40
283 +silent_mode = 0
284 +single_extruder_multi_material = 0
285 +start_gcode = G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nG28 ; home all\nM501 ; Mesh Bed Leveling (Load all saved settings from EEPROM)\nM420 S1 ; Mesh Bed Leveling (Bed Leveling State)\nG1 Y1.0 Z0.3 F1000 ; move print head up\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG92 E0.0\nG92 E0.0\n; initial load\nG1 Y2\nG1 X205.0 E19 F1000\nG1 Y3\nG1 X5.0 E19 F1000\nG92 E0.0\n; intro line\nG1 Y3 Z0.2 F1000\nG1 X65.0 E9.0 F1000\nG1 X105.0 E12.5 F1000\nG92 E0.0
286 +template_custom_gcode =
287 +thumbnails = 16x16,220x124
288 +thumbnails_format = PNG
289 +toolchange_gcode =
290 +use_firmware_retraction = 0
291 +use_relative_e_distances = 1
292 +use_volumetric_e = 0
293 +variable_layer_height = 1
294 +wipe = 1
295 +z_offset = 0
296 +
297 +[presets]
298 +print = 0.20mm QUALITY @ Anycubic Mega X
299 +sla_print =
300 +sla_material =
301 +printer = Anycubic Mega X
302 +filament = Generic PLA @ Anycubic Mega X
303 +physical_printer =
304 +