Zum Inhalt springen

Änderungen von Dokument 3D Drucker

Zuletzt geändert von Fab!an am 2025/04/01 16:54
Von Version 6.1
bearbeitet von Fab!an
am 2024/04/08 08:14
Änderungskommentar: Es gibt keinen Kommentar für diese Version
Auf Version 17.1
bearbeitet von loppermann
am 2024/04/08 08:26
Änderungskommentar: Neuen Anhang PrusaSlicer_config_MegaX.ini hochladen

Zusammenfassung

Details

Seiteneigenschaften
Dokument-Autor
... ... @@ -1,1 +1,1 @@
1 -XWiki.foorschtbar
1 +XWiki.loppermann
Inhalt
... ... @@ -14,8 +14,9 @@
14 14  === Anforderungen ===
15 15  
16 16  * Nicht an den Verstellschrauben für das Heatbed drehen
17 -* Nur mit Mesh-Leveling (Gehört in den Start-G-Code)
18 -:{{code language="none"}}
17 +* Nur mit Mesh-Leveling (Gehört in den Start-G-Code):
18 +
19 +{{code language="gcode"}}
19 19  M501 ; Mesh Bed Leveling (Load all saved settings from EEPROM)
20 20  M420 S1 ; Enable leveling
21 21  M420 Z2.0 ; Set leveling fading height to 2 mm
... ... @@ -36,7 +36,7 @@
36 36  * Die Klammern am Drucker nicht verschieben!
37 37  * Nur mit Mesh-Leveling betreiben! (ist im Prusa Slicer Profil bereits eingestellt)
38 38  
39 -{{code language=""}}
40 +{{code language="gcode"}}
40 40  M501 ; Mesh Bed Leveling (Load all saved settings from EEPROM)
41 41  M420 S1 ; Enable leveling
42 42  M420 Z2.0 ; Set leveling fading height to 2 mm
Plotter_Messer.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.loppermann
Größe
... ... @@ -1,1 +1,0 @@
1 -12.9 MB
Inhalt
netzwerk.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.loppermann
Größe
... ... @@ -1,1 +1,0 @@
1 -64.2 KB
Inhalt
web2dymo.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.loppermann
Größe
... ... @@ -1,1 +1,0 @@
1 -25.6 KB
Inhalt
PrusaSlicer_config_MegaS_Baseplate.stl
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.foorschtbar
Größe
... ... @@ -1,0 +1,1 @@
1 +41.3 KB
Inhalt
PrusaSlicer_config_MegaS_Bundle.ini
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.foorschtbar
Größe
... ... @@ -1,0 +1,1 @@
1 +11.6 KB
Inhalt
... ... @@ -1,0 +1,360 @@
1 +# generated by PrusaSlicer 2.7.0+MacOS-arm64 on 2023-12-05 at 19:59:52 UTC
2 +
3 +[print:WWL 0.20mm QUALITY @MEGA]
4 +arc_fitting = disabled
5 +avoid_crossing_curled_overhangs = 0
6 +avoid_crossing_perimeters = 0
7 +avoid_crossing_perimeters_max_detour = 0
8 +bottom_fill_pattern = monotonic
9 +bottom_solid_layers = 4
10 +bottom_solid_min_thickness = 0.5
11 +bridge_acceleration = 1000
12 +bridge_angle = 0
13 +bridge_flow_ratio = 0.95
14 +bridge_speed = 25
15 +brim_separation = 0
16 +brim_type = outer_only
17 +brim_width = 0
18 +compatible_printers =
19 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/ and nozzle_diameter[0]==0.4
20 +complete_objects = 0
21 +default_acceleration = 1000
22 +dont_support_bridges = 1
23 +draft_shield = disabled
24 +elefant_foot_compensation = 0
25 +enable_dynamic_overhang_speeds = 0
26 +external_perimeter_acceleration = 0
27 +external_perimeter_extrusion_width = 0.45
28 +external_perimeter_speed = 40
29 +external_perimeters_first = 0
30 +extra_perimeters = 1
31 +extra_perimeters_on_overhangs = 0
32 +extruder_clearance_height = 35
33 +extruder_clearance_radius = 60
34 +extrusion_width = 0.45
35 +fill_angle = 45
36 +fill_density = 15%
37 +fill_pattern = gyroid
38 +first_layer_acceleration = 800
39 +first_layer_acceleration_over_raft = 0
40 +first_layer_extrusion_width = 0.42
41 +first_layer_height = 0.2
42 +first_layer_speed = 20
43 +first_layer_speed_over_raft = 30
44 +fuzzy_skin = none
45 +fuzzy_skin_point_dist = 0.8
46 +fuzzy_skin_thickness = 0.3
47 +gap_fill_enabled = 1
48 +gap_fill_speed = 40
49 +gcode_binary = 0
50 +gcode_comments = 0
51 +gcode_label_objects = octoprint
52 +gcode_resolution = 0.0125
53 +gcode_substitutions =
54 +infill_acceleration = 1000
55 +infill_anchor = 2.5
56 +infill_anchor_max = 12
57 +infill_every_layers = 1
58 +infill_extruder = 1
59 +infill_extrusion_width = 0.45
60 +infill_first = 0
61 +infill_overlap = 25%
62 +infill_speed = 60
63 +inherits = 0.20mm QUALITY @MEGA
64 +interface_shells = 0
65 +ironing = 0
66 +ironing_flowrate = 15%
67 +ironing_spacing = 0.1
68 +ironing_speed = 15
69 +ironing_type = top
70 +layer_height = 0.2
71 +max_print_speed = 100
72 +max_volumetric_extrusion_rate_slope_negative = 0
73 +max_volumetric_extrusion_rate_slope_positive = 0
74 +max_volumetric_speed = 0
75 +min_bead_width = 85%
76 +min_feature_size = 25%
77 +min_skirt_length = 4
78 +mmu_segmented_region_interlocking_depth = 0
79 +mmu_segmented_region_max_width = 0
80 +notes =
81 +only_retract_when_crossing_perimeters = 0
82 +ooze_prevention = 0
83 +output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
84 +overhang_speed_0 = 15
85 +overhang_speed_1 = 15
86 +overhang_speed_2 = 20
87 +overhang_speed_3 = 25
88 +overhangs = 1
89 +perimeter_acceleration = 800
90 +perimeter_extruder = 1
91 +perimeter_extrusion_width = 0.45
92 +perimeter_generator = arachne
93 +perimeter_speed = 50
94 +perimeters = 2
95 +post_process =
96 +print_settings_id =
97 +raft_contact_distance = 0.1
98 +raft_expansion = 1.5
99 +raft_first_layer_density = 90%
100 +raft_first_layer_expansion = 3
101 +raft_layers = 0
102 +resolution = 0
103 +seam_position = nearest
104 +single_extruder_multi_material_priming = 1
105 +skirt_distance = 2
106 +skirt_height = 3
107 +skirts = 1
108 +slice_closing_radius = 0.049
109 +slicing_mode = regular
110 +small_perimeter_speed = 25
111 +solid_infill_acceleration = 0
112 +solid_infill_below_area = 0
113 +solid_infill_every_layers = 0
114 +solid_infill_extruder = 1
115 +solid_infill_extrusion_width = 0.45
116 +solid_infill_speed = 50
117 +spiral_vase = 0
118 +staggered_inner_seams = 0
119 +standby_temperature_delta = -5
120 +support_material = 0
121 +support_material_angle = 0
122 +support_material_auto = 1
123 +support_material_bottom_contact_distance = 0
124 +support_material_bottom_interface_layers = -1
125 +support_material_buildplate_only = 0
126 +support_material_closing_radius = 2
127 +support_material_contact_distance = 0.1
128 +support_material_enforce_layers = 0
129 +support_material_extruder = 1
130 +support_material_extrusion_width = 0.35
131 +support_material_interface_contact_loops = 0
132 +support_material_interface_extruder = 1
133 +support_material_interface_layers = 2
134 +support_material_interface_pattern = rectilinear
135 +support_material_interface_spacing = 0.2
136 +support_material_interface_speed = 80%
137 +support_material_pattern = rectilinear
138 +support_material_spacing = 2
139 +support_material_speed = 50
140 +support_material_style = grid
141 +support_material_synchronize_layers = 0
142 +support_material_threshold = 50
143 +support_material_with_sheath = 1
144 +support_material_xy_spacing = 60%
145 +support_tree_angle = 40
146 +support_tree_angle_slow = 25
147 +support_tree_branch_diameter = 2
148 +support_tree_branch_diameter_angle = 5
149 +support_tree_branch_diameter_double_wall = 3
150 +support_tree_branch_distance = 1
151 +support_tree_tip_diameter = 0.8
152 +support_tree_top_rate = 15%
153 +thick_bridges = 1
154 +thin_walls = 0
155 +top_fill_pattern = monotonic
156 +top_infill_extrusion_width = 0.4
157 +top_solid_infill_acceleration = 0
158 +top_solid_infill_speed = 40
159 +top_solid_layers = 5
160 +top_solid_min_thickness = 0.7
161 +travel_acceleration = 0
162 +travel_speed = 180
163 +travel_speed_z = 0
164 +wall_distribution_count = 1
165 +wall_transition_angle = 10
166 +wall_transition_filter_deviation = 25%
167 +wall_transition_length = 100%
168 +wipe_tower = 0
169 +wipe_tower_bridging = 10
170 +wipe_tower_brim_width = 2
171 +wipe_tower_cone_angle = 0
172 +wipe_tower_extra_spacing = 100%
173 +wipe_tower_extruder = 0
174 +wipe_tower_no_sparse_layers = 0
175 +wipe_tower_rotation_angle = 0
176 +wipe_tower_width = 60
177 +wipe_tower_x = 180
178 +wipe_tower_y = 140
179 +xy_size_compensation = 0
180 +
181 +[filament:WWL Generic PLA @MEGA]
182 +bed_temperature = 60
183 +bridge_fan_speed = 100
184 +compatible_printers =
185 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/
186 +compatible_prints =
187 +compatible_prints_condition =
188 +cooling = 1
189 +disable_fan_first_layers = 1
190 +enable_dynamic_fan_speeds = 0
191 +end_filament_gcode = "; Filament-specific end gcode"
192 +extrusion_multiplier = 1
193 +fan_always_on = 1
194 +fan_below_layer_time = 100
195 +filament_colour = #FF3232
196 +filament_cooling_final_speed = 3.4
197 +filament_cooling_initial_speed = 2.2
198 +filament_cooling_moves = 4
199 +filament_cost = 25.4
200 +filament_density = 1.24
201 +filament_deretract_speed = nil
202 +filament_diameter = 1.75
203 +filament_load_time = 0
204 +filament_loading_speed = 28
205 +filament_loading_speed_start = 3
206 +filament_max_volumetric_speed = 10
207 +filament_minimal_purge_on_wipe_tower = 15
208 +filament_multitool_ramming = 0
209 +filament_multitool_ramming_flow = 10
210 +filament_multitool_ramming_volume = 10
211 +filament_notes = ""
212 +filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
213 +filament_retract_before_travel = nil
214 +filament_retract_before_wipe = nil
215 +filament_retract_layer_change = nil
216 +filament_retract_length = nil
217 +filament_retract_length_toolchange = nil
218 +filament_retract_lift = nil
219 +filament_retract_lift_above = nil
220 +filament_retract_lift_below = nil
221 +filament_retract_restart_extra = nil
222 +filament_retract_restart_extra_toolchange = nil
223 +filament_retract_speed = nil
224 +filament_settings_id = ""
225 +filament_soluble = 0
226 +filament_spool_weight = 0
227 +filament_toolchange_delay = 0
228 +filament_travel_lift_before_obstacle = nil
229 +filament_travel_max_lift = nil
230 +filament_travel_ramping_lift = nil
231 +filament_travel_slope = nil
232 +filament_type = PLA
233 +filament_unload_time = 0
234 +filament_unloading_speed = 90
235 +filament_unloading_speed_start = 100
236 +filament_vendor = Generic
237 +filament_wipe = nil
238 +first_layer_bed_temperature = 65
239 +first_layer_temperature = 215
240 +full_fan_speed_layer = 0
241 +idle_temperature = nil
242 +inherits = Generic PLA @MEGA
243 +max_fan_speed = 100
244 +min_fan_speed = 100
245 +min_print_speed = 15
246 +overhang_fan_speed_0 = 0
247 +overhang_fan_speed_1 = 0
248 +overhang_fan_speed_2 = 0
249 +overhang_fan_speed_3 = 0
250 +slowdown_below_layer_time = 20
251 +start_filament_gcode = "; Filament gcode\n"
252 +temperature = 210
253 +
254 +[printer:WWL Anycubic i3 Mega S]
255 +autoemit_temperature_commands = 1
256 +bed_custom_model = Baseplate.stl
257 +bed_custom_texture =
258 +bed_shape = 89x20,101x20,101x6,210x6,210x20,196x20,196x32,210x32,210x190,196x190,196x202,210x202,210x216,126x216,126x202,114x202,114x216,0x216,0x202,14x202,14x190,0x190,0x32,14x32,14x20,0x20,0x6,89x6
259 +before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]
260 +between_objects_gcode =
261 +color_change_gcode = M600
262 +cooling_tube_length = 5
263 +cooling_tube_retraction = 91.5
264 +default_filament_profile = "Generic PLA @MEGA"
265 +default_print_profile = 0.15mm QUALITY @MEGA
266 +deretract_speed = 50
267 +end_gcode = G1 E-1.0 F2100 ; retract\nG92 E0.0\nG1{if max_layer_z < max_print_height} Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} E-34.0 F720 ; move print head up & retract filament\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y105 F3000 ; park print head\nM84 ; disable motors
268 +extra_loading_move = -2
269 +extruder_colour = #808080
270 +extruder_offset = 0x0
271 +gcode_flavor = marlin
272 +high_current_on_filament_swap = 0
273 +host_type = prusalink
274 +inherits = Anycubic i3 Mega S
275 +layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
276 +machine_limits_usage = time_estimate_only
277 +machine_max_acceleration_e = 10000
278 +machine_max_acceleration_extruding = 1250
279 +machine_max_acceleration_retracting = 1250
280 +machine_max_acceleration_travel = 1500,1250
281 +machine_max_acceleration_x = 3000
282 +machine_max_acceleration_y = 2000
283 +machine_max_acceleration_z = 60
284 +machine_max_feedrate_e = 30
285 +machine_max_feedrate_x = 500
286 +machine_max_feedrate_y = 500
287 +machine_max_feedrate_z = 8
288 +machine_max_jerk_e = 5
289 +machine_max_jerk_x = 10
290 +machine_max_jerk_y = 10
291 +machine_max_jerk_z = 0.4
292 +machine_min_extruding_rate = 0,0
293 +machine_min_travel_rate = 0,0
294 +max_layer_height = 0.36
295 +max_print_height = 205
296 +min_layer_height = 0.07
297 +nozzle_diameter = 0.4
298 +parking_pos_retraction = 92
299 +pause_print_gcode = M601
300 +print_host =
301 +printer_model = I3MEGAS
302 +printer_notes = Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_I3_MEGA_S\nPRINTER_HAS_BOWDEN
303 +printer_settings_id =
304 +printer_technology = FFF
305 +printer_variant = 0.4
306 +printer_vendor =
307 +printhost_apikey =
308 +printhost_cafile =
309 +remaining_times = 1
310 +retract_before_travel = 1.5
311 +retract_before_wipe = 60%
312 +retract_layer_change = 1
313 +retract_length = 6
314 +retract_length_toolchange = 10
315 +retract_lift = 0.075
316 +retract_lift_above = 0
317 +retract_lift_below = 204
318 +retract_restart_extra = 0
319 +retract_restart_extra_toolchange = 0
320 +retract_speed = 40
321 +silent_mode = 0
322 +single_extruder_multi_material = 0
323 +start_gcode = G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nG28 ; home all\n; CUSTOM START\nM501 ; Mesh Bed Leveling (Load all saved settings from EEPROM)\nM420 S1 ; Enable leveling\nM420 Z2.0 ; Set leveling fading height to 2 mm\n; CUSTOM END\nG1 Y1.0 Z0.3 F1000 ; move print head up\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG92 E0.0\n; initial load\nG1 X87.0 E19 F1000\nG1 Y1.6\nG1 X5.0 E19 F1000\nG92 E0.0\n; intro line\nG1 Y2.0 Z0.2 F1000\nG1 X35.0 E9.0 F1000\nG1 X87.0 E12.5 F1000\nG92 E0.0
324 +template_custom_gcode =
325 +thumbnails = 16x16/PNG, 220x124/PNG
326 +thumbnails_format = PNG
327 +toolchange_gcode =
328 +travel_lift_before_obstacle = 0
329 +travel_max_lift = 0
330 +travel_ramping_lift = 0
331 +travel_slope = 0
332 +use_firmware_retraction = 0
333 +use_relative_e_distances = 1
334 +use_volumetric_e = 0
335 +variable_layer_height = 1
336 +wipe = 1
337 +z_offset = 0
338 +
339 +[physical_printer:WWL octopi2]
340 +host_type = octoprint
341 +preset_name = WWL Anycubic i3 Mega S
342 +preset_names = "WWL Anycubic i3 Mega S"
343 +print_host = http://octopi2.wwlabs.space
344 +printer_technology = FFF
345 +printhost_apikey = 8A954C5C8EDA4B4CB85B990DBFF6D8E6
346 +printhost_authorization_type = key
347 +printhost_cafile =
348 +printhost_password =
349 +printhost_port =
350 +printhost_ssl_ignore_revoke = 0
351 +printhost_user =
352 +
353 +[presets]
354 +print = WWL 0.20mm QUALITY @MEGA
355 +sla_print =
356 +sla_material =
357 +printer = WWL Anycubic i3 Mega S
358 +filament = WWL Generic PLA @MEGA
359 +physical_printer = WWL octopi2
360 +
PrusaSlicer_config_MegaS_ClampCalibration.stl
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.foorschtbar
Größe
... ... @@ -1,0 +1,1 @@
1 +11.0 KB
Inhalt
PrusaSlicer_config_MegaS_Models.f3d
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.foorschtbar
Größe
... ... @@ -1,0 +1,1 @@
1 +605.1 KB
Inhalt
PrusaSlicer_config_MegaS_Printbed.stl
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.foorschtbar
Größe
... ... @@ -1,0 +1,1 @@
1 +5.4 KB
Inhalt
PrusaSlicer_config_MegaX.ini
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.loppermann
Größe
... ... @@ -1,0 +1,1 @@
1 +9.6 KB
Inhalt
... ... @@ -1,0 +1,304 @@
1 +# generated by PrusaSlicer 2.5.0 on 2023-01-10 at 21:09:30 UTC
2 +
3 +[print:0.20mm QUALITY @ Anycubic Mega X]
4 +avoid_crossing_perimeters = 0
5 +avoid_crossing_perimeters_max_detour = 0
6 +bottom_fill_pattern = monotonic
7 +bottom_solid_layers = 4
8 +bottom_solid_min_thickness = 0.5
9 +bridge_acceleration = 1000
10 +bridge_angle = 0
11 +bridge_flow_ratio = 0.95
12 +bridge_speed = 25
13 +brim_separation = 0
14 +brim_type = outer_only
15 +brim_width = 0
16 +clip_multipart_objects = 1
17 +compatible_printers =
18 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_MEGA_X.*/ and nozzle_diameter[0]==0.4
19 +complete_objects = 0
20 +default_acceleration = 1000
21 +dont_support_bridges = 1
22 +draft_shield = disabled
23 +elefant_foot_compensation = 0
24 +ensure_vertical_shell_thickness = 1
25 +external_perimeter_extrusion_width = 0.45
26 +external_perimeter_speed = 40
27 +external_perimeters_first = 0
28 +extra_perimeters = 1
29 +extruder_clearance_height = 35
30 +extruder_clearance_radius = 60
31 +extrusion_width = 0.45
32 +fill_angle = 45
33 +fill_density = 15%
34 +fill_pattern = gyroid
35 +first_layer_acceleration = 800
36 +first_layer_acceleration_over_raft = 0
37 +first_layer_extrusion_width = 0.42
38 +first_layer_height = 0.2
39 +first_layer_speed = 20
40 +first_layer_speed_over_raft = 30
41 +fuzzy_skin = none
42 +fuzzy_skin_point_dist = 0.8
43 +fuzzy_skin_thickness = 0.3
44 +gap_fill_enabled = 1
45 +gap_fill_speed = 40
46 +gcode_comments = 0
47 +gcode_label_objects = 1
48 +gcode_resolution = 0.0125
49 +gcode_substitutions =
50 +infill_acceleration = 1000
51 +infill_anchor = 2.5
52 +infill_anchor_max = 12
53 +infill_every_layers = 1
54 +infill_extruder = 1
55 +infill_extrusion_width = 0.45
56 +infill_first = 0
57 +infill_only_where_needed = 0
58 +infill_overlap = 25%
59 +infill_speed = 60
60 +inherits =
61 +interface_shells = 0
62 +ironing = 0
63 +ironing_flowrate = 15%
64 +ironing_spacing = 0.1
65 +ironing_speed = 15
66 +ironing_type = top
67 +layer_height = 0.2
68 +max_print_speed = 100
69 +max_volumetric_extrusion_rate_slope_negative = 0
70 +max_volumetric_extrusion_rate_slope_positive = 0
71 +max_volumetric_speed = 0
72 +min_bead_width = 85%
73 +min_feature_size = 25%
74 +min_skirt_length = 4
75 +mmu_segmented_region_max_width = 0
76 +notes =
77 +only_retract_when_crossing_perimeters = 0
78 +ooze_prevention = 0
79 +output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_MegaX_{print_time}.gcode
80 +overhangs = 1
81 +perimeter_acceleration = 800
82 +perimeter_extruder = 1
83 +perimeter_extrusion_width = 0.45
84 +perimeter_generator = arachne
85 +perimeter_speed = 50
86 +perimeters = 2
87 +post_process =
88 +print_settings_id =
89 +raft_contact_distance = 0.1
90 +raft_expansion = 1.5
91 +raft_first_layer_density = 90%
92 +raft_first_layer_expansion = 3
93 +raft_layers = 0
94 +resolution = 0
95 +seam_position = nearest
96 +single_extruder_multi_material_priming = 1
97 +skirt_distance = 2
98 +skirt_height = 3
99 +skirts = 1
100 +slice_closing_radius = 0.049
101 +slicing_mode = regular
102 +small_perimeter_speed = 25
103 +solid_infill_below_area = 0
104 +solid_infill_every_layers = 0
105 +solid_infill_extruder = 1
106 +solid_infill_extrusion_width = 0.45
107 +solid_infill_speed = 50
108 +spiral_vase = 0
109 +standby_temperature_delta = -5
110 +support_material = 0
111 +support_material_angle = 0
112 +support_material_auto = 1
113 +support_material_bottom_contact_distance = 0
114 +support_material_bottom_interface_layers = -1
115 +support_material_buildplate_only = 0
116 +support_material_closing_radius = 2
117 +support_material_contact_distance = 0.1
118 +support_material_enforce_layers = 0
119 +support_material_extruder = 1
120 +support_material_extrusion_width = 0.35
121 +support_material_interface_contact_loops = 0
122 +support_material_interface_extruder = 1
123 +support_material_interface_layers = 2
124 +support_material_interface_pattern = rectilinear
125 +support_material_interface_spacing = 0.2
126 +support_material_interface_speed = 80%
127 +support_material_pattern = rectilinear
128 +support_material_spacing = 2
129 +support_material_speed = 50
130 +support_material_style = grid
131 +support_material_synchronize_layers = 0
132 +support_material_threshold = 50
133 +support_material_with_sheath = 1
134 +support_material_xy_spacing = 60%
135 +thick_bridges = 1
136 +thin_walls = 0
137 +threads = 8
138 +top_fill_pattern = monotonic
139 +top_infill_extrusion_width = 0.4
140 +top_solid_infill_speed = 40
141 +top_solid_layers = 5
142 +top_solid_min_thickness = 0.7
143 +travel_speed = 180
144 +travel_speed_z = 0
145 +wall_distribution_count = 1
146 +wall_transition_angle = 10
147 +wall_transition_filter_deviation = 25%
148 +wall_transition_length = 100%
149 +wipe_tower = 0
150 +wipe_tower_bridging = 10
151 +wipe_tower_brim_width = 2
152 +wipe_tower_no_sparse_layers = 0
153 +wipe_tower_rotation_angle = 0
154 +wipe_tower_width = 60
155 +wipe_tower_x = 180
156 +wipe_tower_y = 140
157 +xy_size_compensation = 0
158 +
159 +[filament:Generic PLA @ Anycubic Mega X]
160 +bed_temperature = 60
161 +bridge_fan_speed = 100
162 +compatible_printers =
163 +compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_MEGA_X.*/
164 +compatible_prints =
165 +compatible_prints_condition =
166 +cooling = 1
167 +disable_fan_first_layers = 1
168 +end_filament_gcode = "; Filament-specific end gcode"
169 +extrusion_multiplier = 1
170 +fan_always_on = 1
171 +fan_below_layer_time = 100
172 +filament_colour = #FF3232
173 +filament_cooling_final_speed = 3.4
174 +filament_cooling_initial_speed = 2.2
175 +filament_cooling_moves = 4
176 +filament_cost = 25.4
177 +filament_density = 1.24
178 +filament_deretract_speed = nil
179 +filament_diameter = 1.75
180 +filament_load_time = 0
181 +filament_loading_speed = 28
182 +filament_loading_speed_start = 3
183 +filament_max_volumetric_speed = 10
184 +filament_minimal_purge_on_wipe_tower = 15
185 +filament_notes = ""
186 +filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
187 +filament_retract_before_travel = nil
188 +filament_retract_before_wipe = nil
189 +filament_retract_layer_change = nil
190 +filament_retract_length = nil
191 +filament_retract_lift = nil
192 +filament_retract_lift_above = nil
193 +filament_retract_lift_below = nil
194 +filament_retract_restart_extra = nil
195 +filament_retract_speed = nil
196 +filament_settings_id = ""
197 +filament_soluble = 0
198 +filament_spool_weight = 0
199 +filament_toolchange_delay = 0
200 +filament_type = PLA
201 +filament_unload_time = 0
202 +filament_unloading_speed = 90
203 +filament_unloading_speed_start = 100
204 +filament_vendor = Generic
205 +filament_wipe = nil
206 +first_layer_bed_temperature = 65
207 +first_layer_temperature = 215
208 +full_fan_speed_layer = 0
209 +inherits =
210 +max_fan_speed = 100
211 +min_fan_speed = 80
212 +min_print_speed = 15
213 +slowdown_below_layer_time = 20
214 +start_filament_gcode = "; Filament gcode\n"
215 +temperature = 210
216 +
217 +[printer:Anycubic Mega X]
218 +bed_custom_model =
219 +bed_custom_texture =
220 +bed_shape = 0x0,300x0,300x300,0x300
221 +before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]
222 +between_objects_gcode =
223 +color_change_gcode = M600
224 +cooling_tube_length = 5
225 +cooling_tube_retraction = 91.5
226 +default_filament_profile = "Generic PLA @MEGA"
227 +default_print_profile = 0.15mm QUALITY @MEGA
228 +deretract_speed = 50
229 +end_gcode = G1 E-1.0 F2100 ; retract\nG92 E0.0\nG1{if max_layer_z < max_print_height} Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} E-34.0 F720 ; move print head up & retract filament\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y105 F3000 ; park print head\nM84 ; disable motors
230 +extra_loading_move = -2
231 +extruder_colour = #808080
232 +extruder_offset = 0x0
233 +gcode_flavor = marlin
234 +high_current_on_filament_swap = 0
235 +host_type = octoprint
236 +inherits =
237 +layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
238 +machine_limits_usage = time_estimate_only
239 +machine_max_acceleration_e = 10000
240 +machine_max_acceleration_extruding = 1250
241 +machine_max_acceleration_retracting = 1250
242 +machine_max_acceleration_travel = 1500,1250
243 +machine_max_acceleration_x = 3000
244 +machine_max_acceleration_y = 2000
245 +machine_max_acceleration_z = 60
246 +machine_max_feedrate_e = 60
247 +machine_max_feedrate_x = 500
248 +machine_max_feedrate_y = 500
249 +machine_max_feedrate_z = 6
250 +machine_max_jerk_e = 5
251 +machine_max_jerk_x = 10
252 +machine_max_jerk_y = 10
253 +machine_max_jerk_z = 0.4
254 +machine_min_extruding_rate = 0,0
255 +machine_min_travel_rate = 0,0
256 +max_layer_height = 0.36
257 +max_print_height = 305
258 +min_layer_height = 0.07
259 +nozzle_diameter = 0.4
260 +parking_pos_retraction = 92
261 +pause_print_gcode = M601
262 +print_host =
263 +printer_model =
264 +printer_notes = Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_MEGA_X\nPRINTER_HAS_BOWDEN
265 +printer_settings_id =
266 +printer_technology = FFF
267 +printer_variant = 0.4
268 +printer_vendor =
269 +printhost_apikey =
270 +printhost_cafile =
271 +remaining_times = 1
272 +retract_before_travel = 1.5
273 +retract_before_wipe = 60%
274 +retract_layer_change = 1
275 +retract_length = 6
276 +retract_length_toolchange = 10
277 +retract_lift = 0.075
278 +retract_lift_above = 0
279 +retract_lift_below = 204
280 +retract_restart_extra = 0
281 +retract_restart_extra_toolchange = 0
282 +retract_speed = 40
283 +silent_mode = 0
284 +single_extruder_multi_material = 0
285 +start_gcode = G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nG28 ; home all\nM501 ; Mesh Bed Leveling (Load all saved settings from EEPROM)\nM420 S1 ; Mesh Bed Leveling (Bed Leveling State)\nG1 Y1.0 Z0.3 F1000 ; move print head up\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG92 E0.0\nG92 E0.0\n; initial load\nG1 Y2\nG1 X205.0 E19 F1000\nG1 Y3\nG1 X5.0 E19 F1000\nG92 E0.0\n; intro line\nG1 Y3 Z0.2 F1000\nG1 X65.0 E9.0 F1000\nG1 X105.0 E12.5 F1000\nG92 E0.0
286 +template_custom_gcode =
287 +thumbnails = 16x16,220x124
288 +thumbnails_format = PNG
289 +toolchange_gcode =
290 +use_firmware_retraction = 0
291 +use_relative_e_distances = 1
292 +use_volumetric_e = 0
293 +variable_layer_height = 1
294 +wipe = 1
295 +z_offset = 0
296 +
297 +[presets]
298 +print = 0.20mm QUALITY @ Anycubic Mega X
299 +sla_print =
300 +sla_material =
301 +printer = Anycubic Mega X
302 +filament = Generic PLA @ Anycubic Mega X
303 +physical_printer =
304 +